ThermOmegaTech Distributor - Washdown and Tepid Water Systems

Key Features of the ThermOmegaTech STVM Washdown Station:

• Interlocking ball valves prevent steam only operation
• Automatic steam shut-off when cold water flow is interrupted
• Thermally activated over temperature shut-off
• Unique Venturi mixing design minimizes water hammer effect
• In-line serviceable mixing valve with easy to replace/clean cartridge

Other Benefits:

• Available in Brass and Stainless Steel
• Interchangeable cartridges converts easily between 185°F and 150°F
• Easy maintenance, limited down time
• Designed to fit in place of competitors hose stations

Key Features:

• No steam required
• Available in stainless steel or brass/bronze construction
• Simple to use and install
• Cost effective
• SmartFlow feature available for additional safety

Available Accessories:

• Hose Assemblies
• Black & White Creamery
• 25’, 50’, & 75’ lengths
• Blue Spray Nozzle
• Brass & Stainless fittings available

DTV valves are available with ½”, ¾”, and 1” NPT water connections.

The DTV can be used in applications where a high temperature discharge flow to a drain/sewer must be tempered with cold water. Examples include:

• Humidifier discharge to sewer/drain
• Commercial dishwashers/warewashers
• Boiler blowdown drain lines
• Autoclave discharge
• Any excessively hot effluent flow to sewer/drain

DVT Design Features:

• Exclusive self-actuating Thermoloid® blend paraffin wax actuator
• Rugged, clog-resistant valve design
• Install using standard pipe fittings and tools
• Operates in any orientation
• Modulates to conserve cooling water
• Effluent tempering capacity limited only by cold water flow rate through DTV

DVT Benefits:

• Self-operating – no external power source required
• Compliant with drain temperature limitations of plumbing codes
• Prevents damage to PVC piping due to over-temperature conditions
• Minimizes water waste
• Easy to install
• Adaptable to almost any drain size

Freeze Protection 

HAT/FP & IC/FP Valves

Benefits:

• Protects against freeze damage
• Self-actuating - requires no external power
• Primary protection or fail-safe backup
• Fast Response
• Discharges minimum amount of water required

HAT/FP:

• Available in ½” & ¾”
• Applications: Safety Showers, Fire Lines, Condensate Systems, Pumps, Backup protection on traced systems
• Available in 303SS body with Brass or 303SS actuator or All 316SS Body and Actuator
• Opens at 35°F and is fully closed at 40°F (other temps are available but with a 10°F curve)
• Ability to sense ambient OR fluid temperature (RF=Reverse Flow)
• Can withstand pressures up to 300 PSIG (ambient sensing) and 150 PSIG (fluid sensing)

IC/FP:

• Available in ½” & ¾”
• Applications: Protection of Piping, Safety Showers, Spray Nozzles or Backup protection for traced systems
• Available in all 303SS, 316SS and Brass
• Opens at 35°F and is fully closed at 40°F
• Only fluid sensing
• Can withstand pressures up to 150 PSIG (1/2”) and 100 PSIG (3/4”)

Scald Protection

HAT/SP & IC/SP Valves

Benefits:

• HAT/SP temperatures up to 105F meet ANSI Z358.1 standards
• Protects safety showers from over-temperature
• conditions, keeping personnel safe
• Self-operating, no power or signal required
• Two wrench flats for easy installation
• Discharges the minimum amount of water required

HAT/SP: 

• Available in ½” & ¾”
• Applications: Safety Showers, outdoor sinks, anywhere scalding can occur
• Available in 303SS body with Brass or 303SS actuator or All 316SS Body and Actuator
• Opens at 105°F and is fully closed at 95°F (other temp options available)
• Ability to sense ambient OR fluid temperature (RF=Reverse Flow)
• Can withstand pressures up to 300 PSIG (ambient) and 150 PSIG (fluid)

IC/SP: 

• Available in ½” & ¾”
• Applications: Solar radiation or overheating in traced lines at point of use
• Available in all 303SS, 316SS and Brass
• Opens at 105°F and is fully closed at 95°F (other temp options available)
• Only fluid sensing
• Can withstand pressures up to 150 PSIG (1/2”) and 100 PSIG (3/4”) 

Therm-O-Mix (TOM Station) Steam Water Heater

Features:

• Instantaneous tepid water for safety shower/eyewash stations
• No electricity is needed
• Plant steam and water do not mix
• Redundant safety controls for over-temperature protection  
• Standard pressure unit available for 45-60 PSIG steam pressure
• Low pressure unit available for 15-30 PSIG steam pressure
• Durable enclosure can be readily removed for service
• Small install footprint – 19 7/8” x 14 ¼” x 26”
• Meets ANSI Z358.1 Standards
• Mixing valve designed to meet ASSE 1071 standards

Emergency Safety Shower (ESS) Electric Water Heater

Features:

• Heavy Duty Construction
• ½” thick Hydrastone cement lining provides tank longevity.
• Copper-silicon alloy tappings cannot rust or corrode.
• High impact composite jacket cannot rust or corrode and eliminates potential damage during installation and transit.
• 3" thick polyurethane foam insulation reduces standby heat loss by over 24% compared to industry standard 2" insulated tanks. Safety
• Factory packaged with the Therm-O-Mix® Station/WWM, a mixing valve designed specifically for emergency drench systems to ensure a constant flow of tepid water per ANSI Z358.1 Standards.
• Mixing valve prohibits delivery of overheated water to prevent scalding.
• Water heater provides tepid water even when an accident causes a loss of electric power.
• Reduces the risk of Legionella because water is stored at an elevated temperature.